Download ModelDownload Sourceembed

About

 

For Teachers

Translations

Code Language Translator Run

Software Requirements

SoftwareRequirements


Android iOS Windows MacOS
with best with Chrome Chrome Chrome Chrome
support full-screen? Yes. Chrome/Opera No. Firefox/ Samsung Internet Not yet Yes Yes
cannot work on some mobile browser that don't understand JavaScript such as.....
cannot work on Internet Explorer 9 and below

 

Credits

This email address is being protected from spambots. You need JavaScript enabled to view it.; Tan Seng Kwang slighted edited

end faq

http://iwant2study.org/lookangejss/02_newtonianmechanics_2kinematics/ejss_model_projectileolevel/projectileolevel_Simulation.xhtml 

Sample Learning Goals

Question on Energy Conversion Primary Science

Primary Science Question on energy Conversion

For Teachers

Activity 1

INVESTIGATE

Go to the following simulation: http://tinyurl.com/ast2016-3 projectile motion

The left panel shows a football being given an initial velocity. This could be zero (the ball is being dropped), upwards (tossed up) or horizontal (thrown horizontally).

The right panel allows you to plot the energy of the object over time. The default is a plot for kinetic energy (ke), but you can also request potential energy (pe), and total energy (te). Remember that you can play the simulation by clicking the appropriate button (►). Click the pause button ( ▌▌) to pause the simulation.

  1. First select the “free_fall” setting, using the yellow drop-down box in the bottom panel. Watch the ke and pe graphs as the object moves. What do you notice about the graphs?
    • suggested answer: kinetic energy increases from t = 0 , KE = 0 J at an increasing rate. Potential energy decreases from t = 0 s, PE = maximum J at an decreasing rate as shown in the sketch. free fall sim
  2. Now try the “toss_up” setting. How are the ke and pe graphs different?
    • suggested answer: kinetic energy decreasing from t = 0 , KE = 50 J at an decreasing rate until t =1 s. From t >1 s,  Kinetic energy increases at an increasing rate. Potential energy increases from t = 0 s to 1 s. From t>1 s, PE decreases at decreasing rate as shown in the sketch. toss up sim
  3. Select total energy te checkbox, suggest an big idea relating ke and pe to te.
    • suggested answer: ke + pe = te ke + pe = te ke + pe = te 
  4. You can alter the reference line for this simulation. Reset the simulation for “free_fall” or for “toss_up” but, before you press play, change the “ref. PE=0 line” to a different value.
    How are the ke and pe graphs different when you choose a different PE reference line?
    • suggested answer: reference PE = 0 is a imaginary line for which potential energy is calculated referencing from. ke is not affected by “ref. PE=0 line” pe referencing line referencing pe line

 

MODEL

You may have noticed that the kinetic energy ke depends on the speed |v|. Now set the simulation to “user_defined”. You can choose the speed you want by typing the value in the magenta box in the bottom. You can read the corresponding kinetic energy ke in the yellow box below the graph in the right-hand panel. Try to fill up the table below.

Speed |v| in m/s Speed x Speed (v2) Kinetic energy ke in J

0.00

 

   

1.00

 

   

2.00

 

   

3.00

 

9.00  

4.00

 

   

5.00

 

  12.5

Now that you have investigated some of the different motions of the football, let’s try to model this by creating some rules about pe and ke. Note that the mass of the ball in the simulation is 1.00 kg, as indicated in the yellow box above the image on the left.

by observing the data is the table, suggest a viable equation-model for ke in terms of v.

suggested answer ke = 0.5*v^2

 

 

  1. Write down some rules for the relationships between pe and ke. Here’s an example:

ke + pe = te

the value of pe is measured from the PE reference line

“The graph for ke does not depend on the PE reference line.”

APPLY

Now try to test your model to see if your rules hold true for a different pre-set motion: “free_fall_and_rebounce”.

  1. Which of your rules are still the same after trying the “free_fall_and_rebounce” setting?
    • ke +pe = te
    • the value of pe is measured from the PE reference line
  2. Which of the rules were not retained?
    • ??, ke = 0.5*v^2 is incomplete, the complete equation is ke = 0.5*m*v^2 where m is the mass of the object.

 

 

Worksheets

  1. Energy - student worksheet (final).docx
  2. Energy - student worksheet (gwf-dl 2).docx
  1.  

    Research

[text]

Video

 

 Version:

  1. http://weelookang.blogspot.sg/2016/03/projectile-energy-simulation.html

Other Resources

[text]

Project related:

Understanding Teacher Learning Community as Support for Implementation of Open Source Physics for Conceptual Instruction
Project Number: OER 10/15 GWF
Project Duration: 01 July 2015 - 30 April 2017

http://weelookang.blogspot.sg/2015/07/understanding-teacher-learning.html

end faq

5 1 1 1 1 1 1 1 1 1 1 Rating 5.00 (1 Vote)